How to Make a Surf Fishing Rod Holder – Exclusive Information

Do you want to improve your own skill by making a surf fishing rod holder? The purpose of making a surf fishing rod holder is to replace the old one by yourself. This experience not only improves your own skills but also reduces the cost of living. Besides, it improves the quality of life and finds new hobbies and develops skills. So, how to make a surf fishing rod holder?

You can easily make a rod holder by following several steps. We have added 3 best tactics for making this type of rod holder. So, without further any due, let’s start the content. 

Why Should You Use a Surf Fishing Rod Holder?

Rod holders have become a necessary tool for fishing. A good fishing rod holder can save your time and make your fishing more fun. This is actually an important part of the gear that you need to get out of the water.

A good casting rod holder will allow you to cast, or simply to hold one or more rods at once. This means that you’ll be able to focus on other things like bait, reeling in the fish. It is also a very important piece of equipment for any fisherman who relies on his skills to catch fish.

Most fishermen are using stainless steel or graphite fishing rods. So you will find a lot of different types of holders in this material.

3 Best Methods to Make a Surf Fishing Rod Holder

Making a surf fishing rod holder is not as difficult as you think. If you have the right tools and plans, making a surf fishing rod holder is actually fun and exciting. With some simple procedures, you can make your own surf fishing rod holder. We have added 3 different methods that will help you to make this type of fishing rod easily. Don’t worry, we are here to guide you. Let’s follow the methods below:

#Method 01

Step 1: Cut a 4′ section PVC pipe using a hacksaw. Use a fine-tooth saw for cutting. This can be done on a designated sawing surface.

Step 2: Fit a 3/4″ to 1/2″ PVC reducer into one end of the PVC pipe. Then, use duct tape to fix it in place.

Step 3: Put the hook into the other end of the PVC pipe. Then, put some duct tape over it to hold it in place.

Step 4: Fit the hook into one end of the PVC pipe until it comes out through the other end. Make sure that it is sticking out about 1/4″ from the other end.

Step 5: You can slide this hook back and forth so as to adjust your fishing plan.

#Method 02

Step 1: First, you need to cut a piece of PVC pipe. It must be at least 2 feet of length.

Step 2: You can purchase a “T” connector as well. One side must be 1/2 inch, while another side should be 3/8 inch connectors.

Step 3: The next step is to find a place to mount the rod holder. Then, you need to drill a hole on the sand spike. Make sure that it is at the top of the sand spike’s tubing.

Step 4: Again, apply some lubricant in the “T” connector. After that, insert the PVC pipe into the “T” connector.

Step 5: Now, take an adjustable rubber roosting ring and put it on the PVC pipe in order to get it locked in its position.

Step 6: Lastly, use a flat head screwdriver in order to tighten up the rubber mounting ring for locking the PVC pipe in its position.

#Method 03

Step 1: Apply some glue to the rail and slide the cut-to-length PVC sections over the end.

Step 2: Drill a hole one size smaller than the diameter of 1/4-inch bolt at the bottom of both 1-foot sections.

Step 3: With the drill on high speed, carefully drill out a 1/4-inch hole around the center of the bolt through both PVC sections.

Step 4: Push the bolt through both sections. Then, Place two washers over the bolt, followed by one wing nut.

Step 5: Tighten the wing nut to secure it in place. Now, Put some glue on one end of a 9-inch section of pipe and slide it over the exposed end of the bolt.

Benefits of Surf Fishing Rod Holder

For someone who is loving outdoor activities and wants to try a new hobby, they can always opt for surf fishing. This activity is fun and can be done by anyone. There are numerous benefits of this surf fishing rod holder. Here are some following benefits of having this holder.

(i) You can easily organize your fishing essentials.

(ii) It is also adjustable to fit fishing rods of different lengths and diameters.

(iii) You don’t have to worry about scratching anything with this holder. Because of the soft silicone around the suction cup end.

(iv) It works well on both smooth and textured surfaces, and it’s also easy to store when not in use.

(v) This surf fishing rod holder is great for beginning anglers.

Precaution That You Should Maintain

There are some precautions that you should maintain for making a surf fishing rod holder. Let’s see them,

(i) Make sure that you need to check the materials of the Spinning Rod or Casting Rod holder because it will impact how well it works.

(ii) If there is any obstruction to it, then it can affect its performance. So, try to avoid obstructions like small fishes and algae as much as possible.

(iii) It’s good to go with a high quality 2- part epoxy for making the mount.

(iv) The reel should be mounted parallel with the board surface.

(v) It’s always necessary to use stainless steel screws and nuts rather than zinc plated ones.

Final Word.

If you have a limited budget on fishing rod holders, then you have to make it yourselves. So, how to make a surf fishing rod holder? In this content, I tried to add all the possible methods to make a surf rod holder.

The fishing rod holder allows you to fish from the beach or from other locations. This can help you save money and reduce injuries. Besides, making a rod holder helps to increase your knowledge.

So guys, if you have any questions related to this fishing rod then you can ask us. Thank You!

2 thoughts on “How to Make a Surf Fishing Rod Holder – Exclusive Information”

Leave a Comment